Powermatic 29 Manuale Utente Pagina 1

Instruction Manual & Parts ListM-0460218(800) 274-6848www.powermatic.comWOOD SHAPERModel 29

10Each half of the aluminum fence should be adjustedas close to the cutterhead as possible without inter-fering with it. Each can be moved independent

112. When the shaping operation removes theentire edge of the stock, e.g. in jointing or making afull bead, the shaped edge will not be supported

12FIGURE 24NOTE: It is advisable to place the cutter as low aspossible on the spindle to reduce spindle deflectionand ensure the best possible finish

13FIGURE 27MAINTENANCEApply a drop of light machine oil occasionally on theledge and wall of the table opening to facilitate thechanging of table inse

14Trouble-Shooting for Model 29 ShaperPROBLEM POSSIBLE CAUSE SOLUTIONShaper will not start. 1. Fuse blown or circuit breaker tripped. 1. Replace f

15(continued)Trouble-Shooting for Model 29 ShaperPROBLEM POSSIBLE CAUSE SOLUTIONCuts not smooth. 1. Wrong R.P.M. 1. Use faster speed.2. Feed too f

16NO. PART NO. DESCRIPTION1 6292984 CHUTE, DUST2 6292985 SCREW, HEX. SOC. SET M8 X 203 6292986 KNOB, ADJUSTMENT4 6292987 PLATE5 6292988 SCREW, ADJ.6 6

17Fence Assembly (29 Shaper)

18PARTS LIST: Spindle Assembly (29 Shaper)NO. PART NO. DESCRIPTION1 6293033 NUT, 3/4" SPINDLE6293034 NUT, 1" SPINDLE6293035 NUT, 1-1/4&quo

19Spindle Assembly (29 Shaper)

Warranty & ServiceThe JET Group warrants every product it sells. If one of our tools needs service or repair, one of our Autho-rized Repair Stati

20PARTS LIST: Shaper Body & Mitre Gauge Assemblies (29 Shaper)NO. PART NO. DESCRIPTION1 6293060 RING, INSERT2 6293061 RING, INSERT3 6293029 SC

21Shaper Body & Mitre Gauge Assemblies (29 Shaper)

22PARTS LIST: Tilting Frame Assembly (29 Shaper)NO. PART NO. DESCRIPTION1 6293124 SCREW, HEX SOC. HD. M10 X 352 6293115 WASHER, M103 6293125 PULLEY

23Tilting Frame Assembly (29 Shaper)

24ELECTRICAL SCHEMATIC: Model 29 Tilting Shaper THREE PHASEY- START(2-STEP SWITCH)D.ONTRAPNOITPIRCSEDEPYTNOITACIFICEPS4703926HCTIWSVER-ROFSCa1

25ELECTRICAL SCHEMATIC: Model 29 Tilting ShaperTHREE PHASE24V.ONTRAPNOITPIRCSEDEPYTNOITACIFICEPS0023926REMROFSNARTTIUCRICLORTNOC.rT45TP4703926HCTIWS

26OPTIONAL ACCESSORIES Model 29 Tilting Shaper6293198 1" Spindle Assembly, 6" under the nut.6293199 1-1/4" Spindle Assembly, 6"

27To order parts or reach our service department, please call our toll-free number between 8:00 a.m. and 4:30 p.m.(CST), Monday through Friday. Havin

CJET Equipment & ToolsP.O. Box 1349Auburn, WA 98071-1349Phone: (800) 274-6848Fax: (800) 274-6840E-mail: [email protected]: ww

TABLE OF CONTENTSSAFETY RULES: General ...

4 GENERAL SAFETY RULESREAD THE MANUAL: Always read the owner'smanual carefully before attempting to use the ma-chine. Know the li

5FIGURE 1FEED STOCK opposite to the direction of thecutter rotation. Never back stock out of the cutteronce the cut has been started. Instead, pull

6RECEIVING THE SHAPERCarefully unpack the shaper and any loose items fromthe wood crate and inspect for damage. Any dam-age should be reported to you

7FIGURE 53. Mount the dust hood (J) to the rear of thefence body (A) with the four cross screws, Figure 6.FIGURE 6MITER GAUGE/CLAMP ASSEMBLYThe miter

8FIGURE 9SPINDLE INSTALLATION& REPLACEMENTThe Model 29 can use interchangeable spindles aswell as router bits. To install the spindle, proceed as

9FIGURE 13RAISING & LOWERING SPINDLE1. Loosen the small handwheel (K), Figure 13.2. Turn large handwheel (L) until spindlereaches the desired h